camelpasta5

Reasons Your Fiat 500 Key Fob Won't Work A key fob from Fiat 500 is a handy way to unlock the doors and start the car. There are a myriad of reasons the fob could stop working. These include a dead coin battery water damage, receiver module issues, and interfering. This listing is for an NEW replacement Fiat Flip Key Remote that looks like the Ilco brand. It has to be professionally programmed (click here to find local locksmiths for your vehicle). This remote includes lock, unlock and trunk buttons. Dead Coin Battery The most common reason your 500 key fob will not work is the battery is dead. Modern key fobs have a restricted operating range, and must be within only a few feet from the vehicle to operate. If you're far away from your vehicle and you press the key fob button, the car won't respond and will display a “Key Fob Not Detected” message in the instrument cluster. If this happens, simply replace the battery of your coin cell (Part number CR2032) with a fresh one from a reliable brand such as Panasonic, Duracell, or Energizer. You can usually find them at your local hardware store, or online. After you've replaced the battery in the coin cell you can test it by standing in front of your Fiat 500 and pressing the buttons. The car will flash its parking lights and the key fob should operate the lock and unlock switches. If your key fob still isn't working even after replacing the battery, there could be water damage that has prevented it from communicating with the module in your vehicle. fiat key cover can occur through a variety of methods, including a simple splash or submerging the key fob into saltwater at the beach. If you believe your fob was exposed to water, place it in a bag of rice to draw out the moisture. If this doesn't work, you will have to get your fob changed by an auto locksmith or dealer. Water Damage While the fob has some rubber seals to keep water out of the chip's electronic circuit and out of the ocean or washing it in a machine could cause water damage. Saltwater is especially dangerous to the circuit board of the fob that can cause it to short out and eventually end up dying. It's not good to submerge the fob in water but don't give up in the event that you accidentally drop it in water or fail to take it out of your pocket. First, remove the battery from the fob. Before replacing the battery, clean the electronic chip with isopropyl or a similar product. Test the fob afterward to determine if it's working. If the key isn't working, it may have to be reprogrammed. This is usually handled by an auto locksmith or dealer. If your key is a bit older and is not programmed to work with your vehicle You will need to replace it completely. A professional locksmith in the automotive industry will be able to complete this process. The locksmith will need to cut the key to match the ignition of your vehicle. They'll also have to reprogram the fob for the car's system. It's a simple and cost-effective process that can usually be completed on the same day. Receiver Module Issues The 500 key fob could stop working because it is out of range. The remote usually has a range of 30 feet or less and if it's far from your vehicle, it won't respond to your commands. It can be solved by moving it closer to your vehicle until it begins responding. If you've replaced the coin battery (commonly known as a “button” or “watch”) and the fob isn't working, it could have an internal circuit board issue. In most cases, reprogramming the fob can resolve the problem. You can find the instructions on how to do this for all vehicles by searching YouTube or reading the owner's manual. It's possible that you need to replace the metal retaining clips that hold the battery of your coin in place. If they lose tension it can prevent the battery from being seated properly, and this will result in the malfunction of your remote. In rare cases the fob could be out of connection with your vehicle as a result of hardware or software issues. You can fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances the software may require reinstallation in your body control modules. Interference Interference can also cause the key fob to not be able to receive or transmit a signal. This could happen when the keyfob's location is in close proximity to a radio transmitter, such as a cell phone or radar detector. Other reasons the key fob might not function include a poor connection to the buttons, damage to the internal chip, or water damage. If your key fob suddenly stopped working, or you have tried everything at home to resolve it (e.g. You might have a damaged 500 receiver module after you've tried replacing the battery, reprogramming it, or using a spare key fob. The receiver module, which is located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It transforms the signals into electronic commands, which are then read by the vehicle. Fortunately, there's an easy method to reset all on-board systems in your 500 device, including the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Then reconnect the battery. This will remove any remaining electricity, and allow you to restart the computer in your car. This could help you get your key fob to work again. If the issue persists, you should consult an expert certified technician. They will be able diagnose the root of any problems.